Methodologies
Technical documentation for each FACT tool: scope, inputs, outputs, underlying data and calculation procedures.
Technical documentation for each FACT tool: scope, inputs, outputs, underlying data and calculation procedures.
Version 1.0, updated September 2026
Board-foot measures are commonly used in U.S. timber markets but are not directly comparable with volume or mass units because the conversion requires clearly defined assumptions and conversion factors. To support a consistent estimation approach to convert timber volumes reported in board feet to metric units, as well as converting those metrics into units of carbon dioxide equivalents (CO2e), this methodology was developed for the Forestry Analytics for Carbon Tracking (FACT) Platform. It supports consistent, transparent, and reproducible conversion procedures and interoperability between FACT tools, and is referred to in the individual methodologies.
Bf: Board feet (wood volume measurement)
CCF: Hundred cubic feet (wood volume measurement)
CO2e: Carbon dioxide equivalent
Dry tons: The oven-dry weight of tree biomass at 0% moisture content, excluding the weight of all water contained in the material.
f3: Cubic feet
FACT: Forestry Analytics for Carbon Tracking
FIA: Forest Inventory and Analysis (program of USDA Forest Service, National Forest Inventory)
Green tons: The weight of freshly cut tree biomass at its natural moisture content, including the water contained in the wood and bark.
HW: Hardwood
m3: Cubic meters
MBF: Thousand board feet (wood volume measurement)
Metric tonnes: Unit of weight equal to 1,000 kilograms (2,204.6 pounds), or approximately 1.102 short tons (t)
NC: North Central (US Region)
NE: Northeast (US Region)
NLS: Northern Lake States (US Region)
PWE: Pacific Northwest, East side (US Region)
PWW: Pacific Northwest, West side (US Region)
PSW: Pacific Southwest (US Region)
RM: Rocky Mountain (US Region)
RMN: Rocky Mountain North (US Region)
RMS: Rocky Mountain South (US Region)
SC: South Central (US Region)
SE: Southeast (US Region)
SW: Softwood
t CO₂e: Metric tonnes of carbon dioxide equivalent
U.S.: United States of America
USDA: United States Department of Agriculture
The goal of this effort was to employ a high-level methodology that balances effort with precision, grounded in best practices and standards as established by the USDA Forest Inventory and Analysis Program (FIA). The bulk of the input data are directly derived from FIA through its EVALIDator application (USDA FS, 2026) or direct FIA queries with a minimum of other inputs restricted to two USFS sources (Miles & Smith, 2009; Smith et al., 2006).
This methodology is grounded around the following objectives:
The methodology is primarily organized as follows:

Figure 1: Roundwood allocation regions.

Figure 2: Product pathway regions.
While all other conversion metrics are based on constants (cubic feet [f3] to cubic meter [m3], green to dry tons, short tons to metric tons) the conversion of board feet to any other volumetric or weight-based unit is defined by the conversion methodology (1/4 inch international, Scribner, Doyle) as well as log dimension.
The resulting conversion matrix allows for crosswalks for the metrics listed below. If a conversion to cubic feet or cord is required, a constant of 35.31 CCF/m3 and 0.276 chord/m3 can be applied, respectively.
The crosswalks providing all relevant calculations and outputs are provided in Annex II. An accompanying Excel spreadsheet labelled ‘FACT mbd to volume conversions [date]’ also contains these tables as well as additional metadata and templates for future updates. It is designed to allow for transparency in data sources and conversion crosswalks with the intent to allow for frequent substitution of inputs based on new time series available (e.g., annual FIA query update) as well as substitution of non-FIA query sources.
For state-wide assessments, all FIA inputs were derived through standardized EVALIDator runs (USDA FS, 2026). The state-level selection of the EVALIDator queries was consistent with US Regions as defined above and illustrated in Figures 1 and 2. In the case of Washington and Oregon where regional delineations do not correspond to state boundaries, FIA queries were run directly. The following EVALIDator inputs were applied:
The following EVALIDator codes were run:
EVALIDator numerator estimation group:
The Pacific Northwest region was divided into a western and eastern section along county boundaries to align with Table D6 in Smith et al. (2006). The EVALIDator query codes described above were manipulated to run straight FIA queries on a multi-county level.
Methodological choices outside of the EVALIDator runs included the following:
Note: the US-wide specific gravity for hardwoods and softwoods as reported by Miles & Smith was only used to facilitate the bark to wood ratio; all other specific gravities reported in the conversion matrix were directly derived from harvested wood by region and based on the most recent FIA inventory.
Miles, P. D., & Smith, W. B. (2009). Specific gravity and other properties of wood and bark for 156 tree species found in North America (NRS-38; pp. 1–35). USDA Forest Service. http://www.fs.usda.gov/treesearch/pubs/34185
Murray, L.T., C. Woodall, A. Lister, K. Stockmann, H. Gu, S. Urbanski, K. Riley, E. Greenfield, et al. 2024. Chapter 5: Quantifying greenhouse gas sources and sinks in managed forest systems. In Hanson, W.L., C. Itle, K. Edquist. (eds.). Quantifying greenhouse gas fluxes in agriculture and forestry: Methods for entity‐scale inventory. Technical Bulletin Number 1939, 2nd edition. Washington, DC: U.S. Department of Agriculture, Office of the Chief Economist. Available at: https://www.usda.gov/oce/entity-scale-ghg-methods/chapter-5
Penman, J., Gytarsky, M., Hiraishi, T., Krug, T., Kruger, D., Pipatti, R., Buendia, L., Miwa, K., Ngara, T., Tanabe, K., & Wagner, F. (2003). Good Practice Guidance for Land Use, Land-Use Change and Forestry (p. 590). International Panel on Climate Change (IPCC).
Smith, J.E., Heath, L.S., Skog, K.E., and Birdsey, R.A. 2006. Methods for calculating forest ecosystem and harvested carbon with standard estimates for forest types of the United States. General Technical Report NE-343. Newtown Square, PA: U.S. Department of Agriculture, Forest Service, Northeastern Research Station. 216 p
USDA FS. (2026). FIADB-API & EVALIDator User Documentation. https://apps.fs.usda.gov/fiadb-api/
Terms specific to this methodology are defined below. See the main FACT Glossary for general terms and for the sources from which definitions are adapted
Carbon (C): The mass of carbon contained within a defined pool (e.g., biomass, dead organic matter or harvested wood products), typically expressed in units of mass (e.g., metric tons of carbon, t C) and derived from biomass using established conversion factors.
CO2e (Carbon dioxide equivalents): A common unit that allows the climate effects of different greenhouse gases to be compared and summed. The quantity of a greenhouse gas is multiplied by its global warming potential (GWP), which expresses its warming effect timbrelative to carbon dioxide over a specified time horizon, conventionally 100 years. The result is reported as the mass of CO₂e that would produce an equivalent climate effect. (Adapted from ISO 14067)
CONUS (Conterminous United States): The 48 states within the contiguous United States, excluding Alaska and Hawaii.
Doyle log rule: A log scaling rule used to estimate the board-foot volume of logs from log length and small-end diameter measured underbark. It is commonly used in the Central and Eastern United States, although use varies by region and market.
EVALIDator: An FIA web application (https://apps.fs.usda.gov/fiadb-api) that allows users to generate population-level estimates and associated sampling errors from the Forest Inventory and Analysis Database (FIADB). Users can select geographic areas, forest attributes, ownerships, forest types and other parameters to estimate metrics such as forest area, tree volume, biomass, growth, removals and mortality.
Forest Inventory and Analysis Program (FIA): A national program of the U.S. Forest Service that conducts continuous, standardized inventories of forest resources across the United States and provides authoritative information on forest extent, composition, structure, growth, removals, and mortality. FIA conducts a variety of inventories, surveys, and reporting activities, including the Nationwide Forest Inventory (NFI), National Resource Use Monitoring (NRUM), National Woodland Owner Survey (NWOS), and Urban Forest Inventory and Analysis (Urban FIA).
Forest Inventory and Analysis Database (FIADB): The publicly available database maintained by the U.S. Forest Service that stores and distributes data collected through FIA, including plot- and tree-level measurements, population estimates and derived forest metrics.
Forest land: FACT applies the so-called “FIA” definition of forest: Forest land has at least 10 percent canopy cover of trees of any size or has had at least 10-percent canopy cover of trees in the past, based on the presence of stumps, snags, or other evidence, and that will be naturally or artificially regenerated. Additionally, the land is not subject to nonforest use(s) that prevent normal tree regeneration and succession, such as regular mowing, intensive grazing or recreation activities. Forest land includes transition zones, such as areas between heavily forested and nonforested lands that are at least 10 percent canopy cover with trees and forest areas adjacent to urban and built-up lands. Also included are pinyon-juniper and other western hardwood areas and afforested areas. The minimum area for classification of forest land is 1 acre (0.4 ha) in size and 120 feet (36.6 m) wide measured stem-to-stem from the outermost edge. Unimproved roads and trails, streams and clearings in forest areas are classified as forest if less than 120 feet wide. For more information, see Forest Definitions Applied in Reporting.
FACT adopts “unreserved forest” as the domain of interest. See Unreserved forest glossary term.
Fuelwood: Roundwood harvested for use as an energy source, such as heat, steam or electricity. This category does not include residues or coproducts generated during the processing of sawlogs or pulpwood and subsequently used as fuel; those materials are accounted for as mill coproducts. Fuelwood is classified separately from industrial roundwood.
Hardwood: Wood produced by angiosperm trees, generally characterized by the presence of vessels or pores. Hardwood species are typically broad-leaved and may be deciduous or evergreen.
International ¼-inch log rule: A log scaling rule used to estimate the board-foot volume of logs from log length and small-end diameter measured underbark, using a ¼-inch saw kerf allowance. It is commonly used in the Eastern United States, although use varies by region and market.
Log scaling rules (Doyle, Scribner, International): Common methods used to estimate the board-foot volume of logs from their dimensions (i.e., Doyle, Scribner, International 1/4 inch log rule). These rules use different assumptions and calculation methods, which can produce different volume estimates for the same log, and their use varies regionally across the United States.
Log type: A classification of harvested roundwood based on its intended use or processing pathway. FACT distinguishes sawlogs, pulpwood, and fuelwood log types. The classification is based on the roundwood categories and harvested wood product accounting methods described in Smith et al. (2006).
Overbark: A scaling approach that includes bark in the estimate of the amount of harvested wood.
Pulpwood: Roundwood intended for processing into pulp, paper, paperboard, or other fiber-or-composite-based wood products. Specifications may vary by region, market and whether dimensions or volumes are expressed on an underbark or overbark basis.
Region: A spatial unit defined by administrative or analytical boundaries that groups states, or portions of states, for the purpose of summarizing and comparing forest attributes. In FACT, regions may be delineated in more than one way depending on how a given dataset is organized, including U.S. Forest Service administrative regions or aggregations of states. In general, regions reflect the finest spatial resolution at which the underlying data in FACT can support reliable estimates.
Sawlog: A log meeting applicable regional or market specifications for diameter, length, and soundness, and where relevant, bark basis, for manufacture into lumber or other solid wood products. Sawlogs are cut from the sawlog portion of sawtimber-size trees.
Scribner log rule: A log scaling rule used to estimate the board-foot volume of logs from log length and small-end diameter measured underbark. It is commonly used in the Western United States and for some Southern pine sawlogs, although use varies by region and market.
Softwood: Wood produced by gymnosperm trees, primarily conifers and generally lacking the vessels or pores characteristic of hardwoods. (Adapted from the FIA Glossary: Standard Terminology)
Underbark: A log scaling approach in which the amount of harvested wood measured or estimated excluding the bark, representing the amount of wood inside the bark as stipulated in the IPCC Production Approach.
Unreserved forest land: Forest land not withdrawn from management by statute or administrative designation, and therefore generally available for multiple uses, including timber production. (Adapted from FIA Glossary: Standard Terminology)
USDA (United States Department of Agriculture): A federal executive department of the United States responsible for developing and implementing policies related to agriculture, forestry, rural development, and food systems, including oversight of programs such FIA.
Wood type: Broad classification of tree species as either hardwood or softwood.
Table 1: Conversion matrix | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Region | Definition | Wood type | Log type | Doyle | International | Scribner | Dry biomass with bark | Green biomass with bark | Carbon biomass with bark | CO2e biomass with bark | Dry wood ( specific gravity) | Green wood | Carbon wood | CO2e wood |
m3/mbf | m3/mbf | m3/mbf | DMT/m3 | GMT/m3 | MT/m3 | MT/m3 | DMT/m3 | GMT/m3 | MT/m3 | MT/m3 | ||||
Pacific Coast | Product pathway region | SW | Sawlog | NA | 4.6 | 6.1 | 0.42 | 0.73 | 0.22 | 0.80 | 0.42 | 0.73 | 0.17 | 0.64 |
Pacific Coast | Product pathway region | HW | Sawlog | NA | 4.9 | 5.8 | 0.42 | 0.75 | 0.22 | 0.80 | 0.42 | 0.74 | 0.22 | 0.81 |
Pacific Northwest - West | Roundwood allocation region | SW | Sawlog | NA | 3.9 | 4.5 | 0.43 | 0.75 | 0.22 | 0.81 | 0.43 | 0.75 | 0.18 | 0.65 |
Pacific Northwest - West | Roundwood allocation region | HW | Sawlog | NA | 4.2 | 4.8 | 0.60 | 1.06 | 0.31 | 1.13 | 0.60 | 1.05 | 0.31 | 1.15 |
Pacific Northwest - East | Roundwood allocation region | SW | Sawlog | NA | 4.2 | 4.8 | 0.44 | 0.76 | 0.23 | 0.83 | 0.44 | 0.76 | 0.18 | 0.66 |
Pacific Northwest - East | Roundwood allocation region | HW | Sawlog | NA | 4.3 | 5.0 | 0.61 | 1.07 | 0.31 | 1.15 | 0.60 | 1.06 | 0.32 | 1.16 |
Pacific Southwest | Roundwood allocation region | SW | Sawlog | NA | 4.6 | 5.2 | 0.43 | 0.75 | 0.22 | 0.81 | 0.43 | 0.75 | 0.18 | 0.65 |
Pacific Southwest | Roundwood allocation region | HW | Sawlog | NA | 5.1 | 6.2 | 0.54 | 0.95 | 0.28 | 1.02 | 0.54 | 0.94 | 0.28 | 1.03 |
Rocky Mountain | Roundwood allocation region, Product pathway region | SW | Sawlog | NA | 4.8 | 5.7 | 0.39 | 0.68 | 0.20 | 0.74 | 0.39 | 0.68 | 0.16 | 0.59 |
Rocky Mountain | Roundwood allocation region, Product pathway region | HW | Sawlog | NA | 4.4 | 5.2 | 0.42 | 0.74 | 0.22 | 0.80 | 0.42 | 0.73 | 0.22 | 0.80 |
Northeast | Roundwood allocation region | SW | Sawlog | 9.3 | 6.2 | NA | 0.38 | 0.67 | 0.20 | 0.73 | 0.38 | 0.67 | 0.16 | 0.58 |
Northeast | Roundwood allocation region | HW | Sawlog | 7.6 | 5.0 | NA | 0.56 | 0.98 | 0.29 | 1.06 | 0.56 | 0.98 | 0.29 | 1.07 |
North Central | Roundwood allocation region | SW | Sawlog | 10.2 | 5.9 | NA | 0.37 | 0.64 | 0.19 | 0.70 | 0.37 | 0.64 | 0.15 | 0.55 |
North Central | Roundwood allocation region | HW | Sawlog | 10.2 | 6.5 | NA | 0.48 | 0.85 | 0.25 | 0.91 | 0.48 | 0.84 | 0.25 | 0.92 |
North | Product pathway region | SW | Sawlog | 9.6 | 6.1 | NA | 0.38 | 0.66 | 0.20 | 0.72 | 0.38 | 0.66 | 0.16 | 0.57 |
North | Product pathway region | HW | Sawlog | 8.6 | 5.6 | NA | 0.52 | 0.92 | 0.27 | 0.99 | 0.52 | 0.91 | 0.27 | 1.00 |
Southeast | Roundwood allocation region | SW | Sawlog | 8.9 | 5.1 | NA | 0.46 | 0.80 | 0.24 | 0.87 | 0.46 | 0.80 | 0.19 | 0.69 |
Southeast | Roundwood allocation region | HW | Sawlog | 7.3 | 5.1 | NA | 0.51 | 0.89 | 0.26 | 0.96 | 0.50 | 0.88 | 0.26 | 0.97 |
South Central | Roundwood allocation region | SW | Sawlog | 7.9 | 5.0 | NA | 0.45 | 0.77 | 0.23 | 0.84 | 0.44 | 0.77 | 0.18 | 0.67 |
South Central | Roundwood allocation region | HW | Sawlog | 7.4 | 5.2 | NA | 0.51 | 0.90 | 0.26 | 0.97 | 0.51 | 0.90 | 0.27 | 0.98 |
South | Product pathway region | SW | Sawlog | 8.6 | 5.1 | NA | 0.45 | 0.79 | 0.23 | 0.85 | 0.45 | 0.79 | 0.19 | 0.68 |
South | Product pathway region | HW | Sawlog | 7.5 | 5.1 | NA | 0.51 | 0.90 | 0.26 | 0.97 | 0.51 | 0.89 | 0.27 | 0.98 |
Pacific Coast* | Product pathway region | SW | Pulpwood | NA | NA | NA | 0.42 | 0.73 | 0.22 | 0.80 | 0.42 | 0.73 | 0.17 | 0.64 |
Pacific Coast* | Product pathway region | HW | Pulpwood | NA | NA | NA | 0.42 | 0.75 | 0.22 | 0.81 | 0.42 | 0.74 | 0.22 | 0.81 |
Pacific Northwest - West* | Roundwood allocation regions | SW | Pulpwood | NA | NA | NA | 0.42 | 0.73 | 0.22 | 0.80 | 0.42 | 0.73 | 0.17 | 0.64 |
Pacific Northwest - West* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.42 | 0.75 | 0.22 | 0.81 | 0.42 | 0.74 | 0.22 | 0.81 |
Pacific Northwest - East* | RPA - split to fit Smith et al 2006 Table D8 | SW | Pulpwood | NA | NA | NA | 0.39 | 0.68 | 0.20 | 0.74 | 0.39 | 0.68 | 0.16 | 0.59 |
Pacific Northwest - East* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.39 | 0.69 | 0.20 | 0.75 | 0.39 | 0.69 | 0.21 | 0.75 |
Pacific Southwest* | Roundwood allocation regions | SW | Pulpwood | NA | NA | NA | 0.42 | 0.73 | 0.22 | 0.80 | 0.42 | 0.73 | 0.17 | 0.64 |
Pacific Southwest* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.42 | 0.75 | 0.22 | 0.81 | 0.42 | 0.74 | 0.22 | 0.81 |
Rocky Mountain* | Roundwood allocation regions, Product pathway region | SW | Pulpwood | NA | NA | NA | 0.39 | 0.68 | 0.20 | 0.74 | 0.39 | 0.68 | 0.16 | 0.59 |
Rocky Mountain* | Roundwood allocation regions, Product pathway region | HW | Pulpwood | NA | NA | NA | 0.42 | 0.74 | 0.22 | 0.80 | 0.42 | 0.73 | 0.22 | 0.80 |
North Central* | Roundwood allocation regions | SW | Pulpwood | NA | NA | NA | 0.38 | 0.67 | 0.20 | 0.73 | 0.38 | 0.67 | 0.16 | 0.58 |
North Central* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.56 | 0.98 | 0.29 | 1.06 | 0.56 | 0.98 | 0.29 | 1.07 |
North* | Roundwood allocation regions | SW | Pulpwood | NA | NA | NA | 0.37 | 0.64 | 0.19 | 0.70 | 0.37 | 0.64 | 0.15 | 0.55 |
North* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.48 | 0.85 | 0.25 | 0.92 | 0.48 | 0.84 | 0.25 | 0.92 |
Northeast* | Product pathway region | SW | Pulpwood | NA | NA | NA | 0.37 | 0.64 | 0.19 | 0.70 | 0.37 | 0.64 | 0.15 | 0.55 |
Northeast* | Product pathway region | HW | Pulpwood | NA | NA | NA | 0.48 | 0.85 | 0.25 | 0.92 | 0.48 | 0.84 | 0.25 | 0.92 |
South Central* | Roundwood allocation regions | SW | Pulpwood | NA | NA | NA | 0.46 | 0.80 | 0.24 | 0.87 | 0.46 | 0.80 | 0.19 | 0.69 |
South Central* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.51 | 0.89 | 0.26 | 0.96 | 0.50 | 0.88 | 0.26 | 0.97 |
Southeast* | Roundwood allocation regions | SW | Pulpwood | NA | NA | NA | 0.45 | 0.77 | 0.23 | 0.84 | 0.44 | 0.77 | 0.18 | 0.67 |
Southeast* | Roundwood allocation regions | HW | Pulpwood | NA | NA | NA | 0.51 | 0.90 | 0.27 | 0.98 | 0.51 | 0.90 | 0.27 | 0.98 |
South* | Product pathway region | SW | Pulpwood | NA | NA | NA | 0.45 | 0.79 | 0.23 | 0.85 | 0.45 | 0.79 | 0.19 | 0.68 |
South* | Product pathway region | HW | Pulpwood | NA | NA | NA | 0.51 | 0.90 | 0.26 | 0.97 | 0.51 | 0.89 | 0.27 | 0.98 |
*Pulp section not retrievable through EVALIDator; Assume same bark-to-wood ratio as saw logs
Table 2: Carbon Content (% dry weight) | ||
|---|---|---|
Wood type | Wood | Bark |
Softwood | 50% | 50% |
Hardwood | 50% | 50% |
Table 3: Green weight conversions (only used for bark:wood ratio calculation) | |||||
|---|---|---|---|---|---|
Moisture content green | |||||
Wood type | Assumption | Wood | Bark | Ratio Bark:Wood | Source |
Softwood | % (oven dry basis) | 74.28% | 70.51% | 0.95 | Miles 2009 |
Hardwood | % (oven dry basis) | 75.12% | 80.64% | 1.07 | Miles 2009 |
Specific gravity | |||||
Wood type | Assumption | Wood | Bark | Ratio Bark:Wood | Source |
Softwood | kg/m3 (oven dry) | 411 | 417 | 1.01 | Miles 2009 |
Hardwood | kg/m3 (oven dry) | 523 | 527 | 1.01 | Miles 2009 |